► Suction Cup Cross Reference List
|
1-11 |
12+ | |||
 |
#18 |
KLUGE, for narrow margin work. Use on feeder or delivery. Same as #17. Rubber disc #19K added for cardboard. |
$12.00/pr | $11.50/pr |
 |
#20 |
WASHERS, Miehle vertical a feed board b gripper bar c gripper head (thin) |
3.60/doz | 3.20/doz |
 |
#21a |
SANDPAPER DISCS, Kluge, C&P, others. Standard 3/4" or extra large 1-1/8". ready glued |
4.50/doz | 4.05/doz |
| #21a - large | 7.00/doz | 6.30/doz | ||
| #21b | without glue | 3.00/doz | 2.70doz | |
| #21b - large | 4.00/doz | 3.60/doz | ||
 |
#26 |
KLUGE METAL CAP, holds standard rubber sucker. For feeder and delivery. |
1.95 | 1.75 |
  |
#27a |
BRASS SUCKER for Chief and Webendorfer Offset Presses, for paper. |
9.50 | 8.55 |
| #27b |
BRASS SUCKER for Chief and Webendorfer Offset Presses, for cardboard. Add a #4, 7, 8, 14 or 15 rubber sucker. |
6.25 | 5.65 | |
  |
#28 |
MIEHLE FEEDER CAP, plastic, shuts off openings on feeder bar. |
2.40/doz | 2.15/doz |
   |
#29a |
MIEHLE VERTICAL, Fluffer Wires for Paper. |
4.50 | 4.05 |
| #29b |
MIEHLE VERTICAL, Fluffer Wires for Cardboard |
4.50 | 4.05 | |
| #29c |
THUMB SCREW, for Fluffer Wires, includes washer. |
.45 | .40 | |
  |
#30a |
MIEHLE VERTICAL, Air Release Valve. Used on feeder are instead of #28 cap. Release a little air by turning screw. Excellent for cardboard and tissue. |
15.00 | 13.50 |
| #30b |
MIEHLE VERTICAL, Cylinder Gripper, Complete only. Fits all Verticals. |
27.00 | 24.30 | |
 |
#32 |
JOB PRESS, Gripper Fingers, Fits Kluges, C&P, etc. Short, long, extra long. Left & Right. Standard & narrow widths. |
4.50 | 4.05 |
| Set of 6 (1 each) | 27.00 | 24.30 | ||
 |
#33a |
KLUGE SHEET TONGUES, Sizes 1-6 |
3.75 | 3.40 |
| Set (1 each #1-6) | 22.50 | 20.25 | ||
| #33b |
SHEET TONGUE SCREW, Fits all Kluges, includes washer. |
.90/pkg(3) | .80/pkg(3) | |
 |
#34 |
MIEHLE VERTICAL TRANSFER TABLE LEVER KEY Keeps feed board in place. Fits all models. |
18.00 | 17.00 |
 |
#35a |
MIEHLE VERTICAL BACKSTOPS, Fits all plain boards. Simple instructions. |
20.00/pr | 19.00/pr |
 |
#36 |
KLUGE REGISTER ROD CAM, Left or right |
51.00 | 45.90 |
 |
#38a |
ENDLESS BELTS, Vertical & Kluge. Leather for drive & motor. |
1-2 |
3+ |
| V-36,V-45,V-50(pre-war) drive: 72" | $157.15 | $147.15 | ||
| V-36,V-45,V-50(pre-war) motor: 43" | call | |||
| V-50 (post-war) drive: 79" | 165.00 | 150.00 | ||
| Kluge 112" | 195.00 | 175.00 |
|
1-11 |
12+ | |||
 |
#39 |
TELESCOPING SUCKER, for ATF Chiefs except Super Chief & Chief 15. Used with flat disc 19K. |
$10.00 | $9.00 |
 |
#40 |
FEED SUCKER BLOCK, for Chief 20, 22, 29 Presses. Convenient thumb screw for adjustment. Holds Part E. |
10.00 | 9.00 |
   |
#41a - small |
PIN WRENCHES VERTICAL Straight type, small and large |
6.00 | 5.40 |
| #41a - large | 24.00 | 21.60 | ||
| #41b | VERTICAL "S" type, small. | 6.00 | 5.40 | |
| #41d | KOMORI pin wrench | Discontinued | ||
 |
#43 | KLUGE REGISTER ROD HOLDER | 31.50 | 28.35 |
 |
#44a |
KLUGE WRENCH SET, 7 piece set. Includes (1)#44b,(2)#44c, (1)#44d, (2)#44e, & (1)#44f |
22.50/set | 20.50/set |
| #44b | Wrench. | 13.50 | 12.00 | |
| #44c | Gripper nut. | .60 | .55 | |
| #44d | Side guide nut. | 6.00 | 5.40 | |
| #44e | Delivery pickup bolt. | .90 | .80 | |
| #44f | Delivery track bolt. | 1.60 | 1.45 | |
 |
#45a |
KLUGE MISCELLANEOUS PARTS, fits
all models. Side guide tongue. (Left or Right) |
5.00/doz | 4.50/doz |
| #45b | Magazine separator spring. | .90 | .80 | |
| #45c | Center comber spring. | 1.00 | .90 | |
| #45d | Side guide eyebolt holds side guide to platen. | 10.00 | 9.00 | |
 |
#48a |
KLUGE Delivery pickup bolt. |
.90 | .80 |
| #48b | Delivery pickup clamp top. | 13.50 | 12.85 | |
| #48c | Delivery pickup clamp base. Specify left or right. | 43.00 | 38.70 | |
| #48d | Delivery pickup suction tube. | 45.00 | 41.50 | |
|
(Left shown) |
#51a |
KLUGE Kluge Side Guide, complete. Left or right. |
60.00 | 54.00 |
| #51a (long) | Kluge Side Guide, complete. Left or right. (w/extra long stem for 12 x 18 press) | 62.00 | 55.80 | |
| #51b | Kluge Side Guide Block. (regular or thick) | 27.00 | 24.3 | |
| #51c | Bottom Feed Gauge. (regular (7/8" l x 1/2" w x 1/8" t), short (1/2" l), thick (1/4" t) or short thick) | 27.00 | 24.30 | |
| #51d | Feed Gauge Tongues only. | 4.50/doz | 4.05/doz | |
| #51e | Kluge Side Guide, complete with offset stem. Left or right. | 69.00 | 62.10 | |
 |
#52a |
KLUGE Kluge Bottom Gauge Band. Specify length - 19-1/2", 23-1/4" or 25-1/2" |
12.00 | 11.00 |
| #52b | Kluge Bottom Gauge Band Clamp. Quick release. | 35.00 | 31.50 | |
| #52c | Kluge Bottom Gauge Band Clamp with screw to hold band. Specify left or right. | 35.00 | 31.50 | |
 |
#53 |
BLOWER FLEXIBLE STEEL TUBING Fits all Kluges. 5' length. |
31.50 | 29.00 |
 |
#54a |
KLUGE Cardboard , left KG-571 |
39.00 | 35.10 |
| #54b | Cardboard, right KG-571A | 39.00 | 35.10 | |
 |
#54c | Paper, left KG-577 | 39.00 | 35.10 |
| #54d | Paper, right KG-5771A | 39.00 | 35.10 | |
 |
#54e | Dummy KG-580 | 33.00 | 29.70 |
 |
#65 |
SHEET SEPARATORS, (Cat Whiskers). For small offset presses. |
1-5 doz | 6-11 doz | 12+doz | ||
| Multilith or Hamada: Brass | $5.00 | $4.50 | $4.05 | ||||
| Multilith or Hamada: Bronze | 6.25 | 5.65 | 5.10 | ||||
| Chief 15/17 | 6.25 | 5.65 | 5.10 | ||||
| Davidson: Brass | 4.75 | 4.30 | 3.90 | ||||
| Komori, Fuji, or Hashimoto | 9.50 | 8.55 | 7.70 | ||||
| Komori, Fuji, or Hashimoto: Heavy | 9.50 | 8.55 | 7.70 | ||||
| Ryobi-Itek | 8.00 | 7.20 | 6.50 | ||||
|
1-11 |
12+ | |||
 |
#69 |
GRIPPER BOLTS, for C&P or Kluge. Sold in pairs. |
$3.75/pr | $3.25/pr |
 |
#70 |
RYOBI/ITEK, telescoping sucker. Comes with #19K discs. |
22.00 | 19.80 |
 |
#71 |
MIEHLE VERTICAL, telescoping sucker for cardboard and envelopes. Fits existing shoe. Comes with #30A vacuum valve and #19K discs. |
Discontinued |
|
 |
#72 |
MIEHLE VERTICAL, telescoping sucker. Comes with #19K discs. |
Discontinued |
|
 |
#73 |
A.B. DICK metal telescoping sucker. Comes with #19K discs. For difficult and wavy stock. |
22.00 | 19.80 |
 |
#73p |
A.B. DICK Plastic telescoping sucker with shut-off valve. Comes with a #66 sucker. |
9.75 | 8.80 |
 |
#74a&b |
MULTILITH or HAMADA telescoping suckers. Uses #19K discs. For difficult and wavy stock. |
45.00/set | 42.50/set |
 |
#74c |
NEW STYLE MULTILITH, telescoping sucker. 1250-1250W and 1850. Comes with #19K discs. |
22.00 | 19.80 |
 |
#75 |
CHIEF 15 & 17, telescoping sucker. Uses #19K or 19-AB DICK discs. For difficult and wavy stock. |
22.00 | 19.80 |
 |
#6008 8x12 | Job Press Grippers For C&P, Kluge, and other job presses taking similar grippers. Job Press Gripper Fingers (#32) snap on tightly, holding sheets rigid, preventing slurs. One set consists of a left and right gripper and 3 pairs #32 gripper fingers | 60.00/set | 54.00/set |
| #6010 10x15 | 72.00/set | 64.80/set | ||
| #6012 12x18 | 78.00/set | 70.20/set | ||
| All prices each unless noted. Sizes, styles, colors, etc can not be combined for quantity pricing. For larger quantities please call. Manufacturer part numbers listed for reference purposes only. Samples available. |
| ►Back to top |
